ESPEasy: Difference between revisions

Latest revision as of 14:19, 15 April 2024

This is about ESP32 and ESP8622 microcontrollers

Flash the firmware

Flash!
Ah-ah
Saviour of the universe!

$ sudo apt install --yes esptool
$ wget https://github.com/letscontrolit/ESPEasy/releases/download/mega-20200515/ESPEasy_mega-20200515.zip
$ esptool --port /dev/ttyUSB0 --baud 115200 write_flash 0 ESP_Easy_mega_20200516_test_beta_ESP8266_4M1M.bin
esptool.py v2.8
Serial port /dev/ttyUSB0
Connecting...
Detecting chip type... ESP8266
Chip is ESP8266EX
Features: WiFi
Crystal is 26MHz
MAC: 3c:71:bf:2a:a6:0b
Enabling default SPI flash mode...
Configuring flash size...
Auto-detected Flash size: 4MB
Erasing flash...
Took 2.33s to erase flash block
Writing at 0x000dbc00... (87 %)

ESP32 WROOM32

$ esptool --port /dev/ttyUSB1 --baud 512000 write_flash -fs 4MB -fm dout 0x0 bin/ESP_Easy_mega_20240414_collection_A_ESP32_4M316k.factory.bin

Connect via Serial

$ minicom -D /dev/ttyUSB0 --baudrate 115200
Welcome to minicom 2.8

OPTIONS: I18n 
Port /dev/ttyUSB0, 10:28:08

Press CTRL-A Z for help on special keys

Posssible commands via serial connection

You do not see what you type until you hit enter, then you will see the command you have entered and the result, like:

>Save

OK

You can find all commands here: ESPEasy/docs/source/Plugin/P000_commands.repl.
This is just a subset:

Get the Allowed IP range

AccessInfo

Get the build number

Build

Clear allowed IP range for the web interface for the current session

ClearAccessBlock

Clear the password of the unit

ClearPassword

Get or set the date and time

Datetime[,YYYY-MM-DD[,hh:mm:ss]]

Get or set DNS configuration

DNS[,<IP address>]

Get or set serial port debug level

Debug[,<1-4, default is 2>]

Get or set the gateway configuration

Gateway[,<IP address>]

Run I2C scanner to find connected I2C chips. Output will be sent to the serial port

I2Cscanner

Get or set IP address

IP[,<IP address>]

Set the password of the unit

Password <mypassword>

Reboot

Reboot

Reset config to factory default. Caution, all settings will be lost!

Be careful! Do you want this? This deletes the whole configuration but not the Firmware.

Reset

Save config to persistent flash memory

Save

Show settings on serial terminal

Settings

TimeZone

TimeZone[,<minutes from UTC>]

Get or set the status of NTP (Network Time Protocol)

UseNTP[,<0/1>]

Configure your local wifi credentials

WifiSSID <myssid>
WifiKey <mypassword>
WifiConnect

MQTT

Controller

Configure MQTT connection to the broker like this:

Click on Add
Choose Type openHAB
Enter your parameters like this where banana1.fritz.box in this example is the server your MQTT broker is running at.

Device

Now you need to listen on MQTT events. For that you need to configure a Generic - MQTT Import device:

Click on Add
Choose Type Generic MQTT Import
Enter your parameters like this where MQTT is the event name for the #Rules and MQTT Topic n are the topics you listen at.

Rules

Switch relays based on MQTT events

On my relay board ESP12F_Relay_X4 I configured #MQTT and use rules to switch the 4 relays.

on system#boot do
  let,1,15                               // Relay 1 is GPIO15
  let,2,14                               // Relay 2 is GPIO14
  let,3,12                               // Relay 3 is GPIO12
  let,4,13                               // Relay 4 is GPIO13
endon

on MQTT#Relay* do
  if %eventvalue1%<0                   
    //
    // Values below 0 sets timer to %eventvalue1%*-1 seconds
    //
    let,5,abs(%eventvalue1%)
    logentry,"%eventname%: Turn on {substring:5:11:%eventname%} (GPIO%v{substring:10:11:%eventname%}%) for %v5% seconds."
    timerSet,{substring:10:11:%eventname%},%v5%
    gpio,%v{substring:10:11:%eventname%}%,1
  elseif %eventvalue1%=1
    //
    // Value equal 1 turn on relay
    //
    logentry,"%eventname%: Turn on {substring:5:11:%eventname%} (GPIO%v{substring:10:11:%eventname%}%)."
    gpio,%v{substring:10:11:%eventname%}%,1
  elseif %eventvalue1%=0
    //
    // Value equal 0 turn off relay
    //
    logentry,"%eventname%: Turn off {substring:5:11:%eventname%} (GPIO%v{substring:10:11:%eventname%}%)."
    timerSet,{substring:10:11:%eventname%},0
    gpio,%v{substring:10:11:%eventname%}%,0
  endif
endon

on Cron#Relay4 do
  logentry,"%eventname%: Turn on Relay4."
  gpio,%v4%,1
  timerSet,4,30
endon

on Rules#Timer do
  logentry,"%eventname%: %eventvalue1% GPIO%v%eventvalue1%%"
  gpio,%v%eventvalue1%%,0
endon

Problems

interface 0 claimed by ch341 while 'brltty' sets config #1

Oct  9 14:40:06 lollybook kernel: [372389.769039] usb 3-1.4.3: ch341-uart converter now attached to ttyUSB0
Oct  9 14:40:07 lollybook kernel: [372390.769995] usb 3-1.4.3: usbfs: interface 0 claimed by ch341 while 'brltty' sets config #1
Oct  9 14:40:07 lollybook kernel: [372390.771187] ch341-uart ttyUSB0: ch341-uart converter now disconnected from ttyUSB0
Oct  9 14:40:07 lollybook kernel: [372390.771258] ch341 3-1.4.3:1.0: device disconnected

I found this:

Unable to use USB dongle based on USB-serial converter chip

for f in /usr/lib/udev/rules.d/*brltty*.rules; do
    sudo ln -s /dev/null "/etc/udev/rules.d/$(basename "$f")"
done
sudo udevadm control --reload-rules

But I also had to disable the brltty-udev.service

$ sudo systemctl stop brltty-udev.service
$ sudo systemctl mask brltty-udev.service
Created symlink /etc/systemd/system/brltty-udev.service → /dev/null.

After disabling brltty I finally got:

Oct  9 14:41:30 lollybook kernel: [372473.985072] ch341 3-1.4.3:1.0: ch341-uart converter detected
Oct  9 14:41:30 lollybook kernel: [372473.987063] usb 3-1.4.3: ch341-uart converter now attached to ttyUSB0