ESPEasy

From Lolly's Wiki
Revision as of 10:40, 18 November 2022 by Lollypop (talk | contribs) (→‎MQTT)
Jump to navigationJump to search


Flash the firmware

Flash!
Ah-ah
Saviour of the universe!

$ sudo apt install --yes esptool
$ wget https://github.com/letscontrolit/ESPEasy/releases/download/mega-20200515/ESPEasy_mega-20200515.zip
$ esptool --port /dev/ttyUSB0 --baud 115200 write_flash 0 ESP_Easy_mega_20200516_test_beta_ESP8266_4M1M.bin
esptool.py v2.8
Serial port /dev/ttyUSB0
Connecting...
Detecting chip type... ESP8266
Chip is ESP8266EX
Features: WiFi
Crystal is 26MHz
MAC: 3c:71:bf:2a:a6:0b
Enabling default SPI flash mode...
Configuring flash size...
Auto-detected Flash size: 4MB
Erasing flash...
Took 2.33s to erase flash block
Writing at 0x000dbc00... (87 %)

Connect via Serial

$ minicom -D /dev/ttyUSB0 --baudrate 115200
Welcome to minicom 2.8

OPTIONS: I18n 
Port /dev/ttyUSB0, 10:28:08

Press CTRL-A Z for help on special keys

Posssible commands via serial connection

You do not see what you type until you hit enter, then you will see the command you have entered and the result, like:

>Save

OK

You can find all commands here: ESPEasy/docs/source/Plugin/P000_commands.repl.
This is just a subset:

Get the Allowed IP range

  • AccessInfo

Get the build number

  • Build

Clear allowed IP range for the web interface for the current session

  • ClearAccessBlock

Clear the password of the unit

  • ClearPassword

Get or set the date and time

  • Datetime[,YYYY-MM-DD[,hh:mm:ss]]

Get or set DNS configuration

  • DNS[,<IP address>]

Get or set serial port debug level

  • Debug[,<1-4, default is 2>]

Get or set the gateway configuration

  • Gateway[,<IP address>]

Run I2C scanner to find connected I2C chips. Output will be sent to the serial port

  • I2Cscanner

Get or set IP address

  • IP[,<IP address>]

Set the password of the unit

  • Password <mypassword>

Reboot

  • Reboot

Reset config to factory default. Caution, all settings will be lost!

Be careful! Do you want this? This deletes the whole configuration but not the Firmware.

  • Reset

Save config to persistent flash memory

  • Save

Show settings on serial terminal

  • Settings

TimeZone

  • TimeZone[,<minutes from UTC>]

Get or set the status of NTP (Network Time Protocol)

  • UseNTP[,<0/1>]


Configure your local wifi credentials

  • WifiSSID <myssid>
  • WifiKey <mypassword>
  • WifiConnect

MQTT

Configuring MQTT on ESPEasy like this:

  • Click on Add
  • Choose Type openHAB
  • Enter your parameters like this where banana1.fritz.box in this example is the server your MQTT broker is running at.


Rules

Switch relays based on MQTT events

On my relay board ESP12F_Relay_X4 I configured #MQTT and use rules to switch the 4 relays.

on MQTT#Relay* do
  let,1,15                               // Relay 1 is GPIO15
  let,2,14                               // Relay 2 is GPIO14
  let,3,12                               // Relay 3 is GPIO12
  let,4,13                               // Relay 4 is GPIO13
  if %eventvalue1%<0                   
    //
    // Values below 0 sets timer to %eventvalue1%*-1 seconds
    //
    let,5,abs(%eventvalue1%)
    logentry,"%eventname%: Turn on {substring:5:11:%eventname%} (GPIO%v{substring:10:11:%eventname%}%) for %v5% seconds."
    timerSet,{substring:10:11:%eventname%},%v5%
    gpio,%v{substring:10:11:%eventname%}%,1
  elseif %eventvalue1%=1
    //
    // Value equal 1 turn on relay
    //
    logentry,"%eventname%: Turn on {substring:5:11:%eventname%} (GPIO%v{substring:10:11:%eventname%}%)."
    gpio,%v{substring:10:11:%eventname%}%,1
  elseif %eventvalue1%=0
    //
    // Value equal 0 turn off relay
    //
    logentry,"%eventname%: Turn off {substring:5:11:%eventname%} (GPIO%v{substring:10:11:%eventname%}%)."
    gpio,%v{substring:10:11:%eventname%}%,0
  endif
endon

on Rules#Timer do
  logentry,"Eventname %eventname%: %eventvalue1% GPIO%v%eventvalue1%%"
  gpio,%v%eventvalue1%%,0
endon

Problems

interface 0 claimed by ch341 while 'brltty' sets config #1

Oct  9 14:40:06 lollybook kernel: [372389.769039] usb 3-1.4.3: ch341-uart converter now attached to ttyUSB0
Oct  9 14:40:07 lollybook kernel: [372390.769995] usb 3-1.4.3: usbfs: interface 0 claimed by ch341 while 'brltty' sets config #1
Oct  9 14:40:07 lollybook kernel: [372390.771187] ch341-uart ttyUSB0: ch341-uart converter now disconnected from ttyUSB0
Oct  9 14:40:07 lollybook kernel: [372390.771258] ch341 3-1.4.3:1.0: device disconnected

I found this:

for f in /usr/lib/udev/rules.d/*brltty*.rules; do
    sudo ln -s /dev/null "/etc/udev/rules.d/$(basename "$f")"
done
sudo udevadm control --reload-rules

But I also had to disable the brltty-udev.service

$ sudo systemctl stop brltty-udev.service
$ sudo systemctl mask brltty-udev.service
Created symlink /etc/systemd/system/brltty-udev.service → /dev/null.

After disabling brltty I finally got:

Oct  9 14:41:30 lollybook kernel: [372473.985072] ch341 3-1.4.3:1.0: ch341-uart converter detected
Oct  9 14:41:30 lollybook kernel: [372473.987063] usb 3-1.4.3: ch341-uart converter now attached to ttyUSB0