NetApp and Linux: Difference between revisions
m (Text replacement - "[[Kategorie:" to "[[Category:") |
m (Text replacement - "<source" to "<syntaxhighlight") |
||
| Line 4: | Line 4: | ||
Maybe this works: | Maybe this works: | ||
< | <syntaxhighlight lang=bash> | ||
# fdisk -l /dev/sda | awk '/^\/dev\//{fieldnum=2;if($fielnum=="*"){fieldnum++}blockalign=$fieldnum/8;if(blockalign!=int(blockalign)){match($0,$fieldnum);printf "%s <<<<<<< Bucket %d\n",substr($0,0,RSTART-2)"_"substr($0,RSTART,RLENGTH)"_"substr($0,RSTART+RLENGTH+1),8*(blockalign-int(blockalign));}else{print $0;}next;}{print;}' | # fdisk -l /dev/sda | awk '/^\/dev\//{fieldnum=2;if($fielnum=="*"){fieldnum++}blockalign=$fieldnum/8;if(blockalign!=int(blockalign)){match($0,$fieldnum);printf "%s <<<<<<< Bucket %d\n",substr($0,0,RSTART-2)"_"substr($0,RSTART,RLENGTH)"_"substr($0,RSTART+RLENGTH+1),8*(blockalign-int(blockalign));}else{print $0;}next;}{print;}' | ||
| Line 25: | Line 25: | ||
==Remove multipath LUNs== | ==Remove multipath LUNs== | ||
This writes out the commands to delete multipathed devices for filer <filer> (empty volumes parameter to gawk means all volumes): | This writes out the commands to delete multipathed devices for filer <filer> (empty volumes parameter to gawk means all volumes): | ||
< | <syntaxhighlight lang=bash> | ||
( sanlun lun show -p <filer> ; echo ) | gawk -v volumes="/vol/vol1:/vol/vol2"' | ( sanlun lun show -p <filer> ; echo ) | gawk -v volumes="/vol/vol1:/vol/vol2"' | ||
BEGIN { | BEGIN { | ||
Revision as of 23:11, 25 November 2021
Check partitioning
Maybe this works: <syntaxhighlight lang=bash>
- fdisk -l /dev/sda | awk '/^\/dev\//{fieldnum=2;if($fielnum=="*"){fieldnum++}blockalign=$fieldnum/8;if(blockalign!=int(blockalign)){match($0,$fieldnum);printf "%s <<<<<<< Bucket %d\n",substr($0,0,RSTART-2)"_"substr($0,RSTART,RLENGTH)"_"substr($0,RSTART+RLENGTH+1),8*(blockalign-int(blockalign));}else{print $0;}next;}{print;}'
Disk /dev/sda: 17.2 GB, 17179869184 bytes 64 heads, 32 sectors/track, 16384 cylinders, total 33554432 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d6bea
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 13672447 6835200 83 Linux /dev/sda2 _13674494_ 33552383 9938945 5 Extended <<<<<<< Bucket 6 /dev/sda5 13674496 25391103 5858304 83 Linux /dev/sda6 25393152 33552383 4079616 82 Linux swap / Solaris </source>
Partition 2 does not matter because it is just metadata of partitioning. We are aligned!
Remove multipath LUNs
This writes out the commands to delete multipathed devices for filer <filer> (empty volumes parameter to gawk means all volumes): <syntaxhighlight lang=bash> ( sanlun lun show -p <filer> ; echo ) | gawk -v volumes="/vol/vol1:/vol/vol2"' BEGIN {
split(volumes,vols,":");
} /ONTAP Path:/,/^$/ {
if(/ONTAP Path:/){
opath=$NF;
if (volumes==""){
todelete="yes";
}else{
odev=$NF;
gsub(/^.*:/,"",odev);
for(vol in vols){
if (odev == vols[vol] || volumes==""){
todelete="yes";
}
}
}
}
if(todelete!="yes")next;
if(/Host Device:/){
command="dmsetup info --columns --noheadings -o open /dev/mapper/"$NF;
command | getline inuse;
close(command);
if (inuse!=0) {
printf "#\n## Device %s (%s) is in use!!!\n## check with: lsof | grep \"$(dmsetup info --columns --noheadings --separator \",\" -omajor,minor /dev/mapper/%s)\"\n#\n",$NF,opath,$NF;
} else {
printf "multipath -w %s\n",$NF;
printf "multipath -f /dev/mapper/%s && (\n",$NF;
}
};
if(inuse==0 && $2 ~ /(primary|secondary)/){
printf "echo 1 > /sys/block/%s/device/delete\n",$3;
}
if (inuse==0 && /^$/) { printf ")\n";}
} /^$/ {
mpathdevice=""; todelete="no"; delete devices;
} ' </source>
